It is no secret that many patients of the cosmetology clinic do not agree to injection procedures, because they are terrified of injections. This panic is usually associated with the expectation of pain. In addition to injections, some hardware procedures, mechanical cleanings, and other manipulations can also cause pain. The introduction of analgesics to improve patient comfort is not always possible for a number of reasons, and then topical drugs come to the rescue. Read about how to anesthetize the skin on estet-portal.com.
How does the drug work, which can anesthetize the skin
OnCosmetics offers cosmetologists a combination drug Lightfrost, designed to locally reduce pain and discomfort during procedures.
If before an injection or other manipulation the question arises of how to anesthetize the skin and calm the patient, especially when he is the owner of sensitive skin, Lightfrost will be a good choice.
Lightfrost gel is used for pain relief not only during care procedures, but also for other manipulations that are accompanied by pain:
- epilation,
- piercing, earlobe piercings,
- tattooing.
The action of Lightfrost is based on blocking the formation of a pain impulse in the nerve endings and its transmission along the nerve fibers. After applying the anesthetic gel, the patient does not feel pain from manipulation, but at the same time retains skin sensitivity to touch, to temperature changes.
Before you anesthetize the skin with Lightfrost gel, you should determine the depth and strength of the planned effect on the skin. The fact is that the level of desensitization does not depend on the amount of the drug that is applied to the skin, but on the duration of the period during which it is on it. So, for example, for epilation of unwanted hair on the legs, you can keep the gel on the skin less than when planning epilation in the bikini area.
Features of the effect of the product: how to anesthetize the skin with high sensitivity
The peculiarity of Lightfrost gel is that it is made on a water basis, which means it is especially good for sensitive skin - it does not cause irritation, it is perfectly absorbed and has a moisturizing effect.
Applied to the skin, Lightfrost gel should be kept moist longer so that the active pain-relieving ingredients penetrate as deeply as possible and are evenly distributed in the tissues, providing a lasting effect.
The higher the concentration of the gel in the zone of the forthcoming manipulation, the more effective will be the penetration of the anesthetic components of the drug through the intact skin epithelium and the better the effect.
Another feature of the Lightfrost gel is the presence of an anestoderm complex in its composition. The complex is a combination of substances that effectively and safely relieve pain and at the same time enhance each other's action. Anestoderm-complex provides excellent clinical efficacy of the Lightfrost gel, and if the doctor correctly follows all recommendations for the use of the drug, then the patient is ensured the loss of any discomfort whatsoever. Any procedure associated with superficial exposure to the skin is easy and calm for patients.
Depending on the individual sensitivity threshold of the patient and on the area of application of the Lightfrost gel (the number of sensitive nerve endings in the treatment area), the maximum severity of the analgesic effect occurs after 15-60 minutes and lasts for about 4 hours. Further, the effect of the active components weakens, and sensitivity gradually returns to the tissues in its full volume.
How to properly use a remedy that can anesthetize the skin
Before anesthetizing the skin with Lightfrost gel, there are some precautions to be taken, especially if the cosmetologist has not used this preparation before.
- The gel must be applied in doses - only on the area of the skin that will be processed immediately; avoid simultaneous application of the drug to several large areas.
- If you need to carry out a series of painful procedures on different parts of the body, you should divide them into several days and carry out sequentially: for example, anesthetize and epilate the face area on one day, the bikini area on the other.
- When applying Lightfrost gel for the first time, it is mandatory to test the sensitivity of the patient: if 30 minutes after applying the drug to the inner elbow, the skin does not turn red, you can continue the procedure.
Lightfrost Gel is generally well tolerated by patients and does not cause irritation or allergies. Its use provides the patient with a high level of comfort during the cosmetic procedure, helps to overcome the psychological fear of possible pain from an injection or other doctor's manipulation.
Add a comment